Replacing uPVC Window Handles
The replacement of window handles made of upvc is a simple task. It is important to ensure that the new handle is a good fit for the spindle carved out in the window mechanism.
If the steps listed below are followed properly the cockspur handle will fit most windows. The most important factor is the step size of the handle.
What to look for
As time passes, uPVC handles on many windows in the UK may begin to show signs wear and tear. The handle on the window may become shaky or difficult to operate when this occurs. Anyone who is familiar using a basic hand tool can complete this relatively simple task.
The first step is to make sure that the handle is securely attached to the window frame and in an open position. The next step is to locate the pins or screws that secure the handle in place. These are usually located on the inside of the handle. They can be removed using a screwdriver and pliers.
Once the handle has become loose, gently pull it away from its hinges. Then, you'll have to locate a replacement handle in the same size and style. This can be done in the DIY store or on the internet. The process should take about five minutes, and you will need a screwdriver.
The most important thing to consider when replacing the uPVC window handle is its step height. This is the distance from the bottom of the handle to where it rests on the window frame. This is a common measurement and you should confirm the height of the step before purchasing the replacement handle.
Depending on the type of handle you are using There are various sizes that are available. Inline handles for uPVC windows usually have 31mm lug centres as well as varieties of cockspur handles with 43mm centres. Repair My Windows And Doors -and-turn handles are common on uPVC windows. They feature a unique design that allows the window to be slid down to let in air and then turned to fully open the window.
The most frequent breakage in uPVC handles is that they crack inside instead of breaking away from the base section. This makes them difficult to open and therefore it is important to make sure that any replacement handle you buy has the same length of spindle as your existing one.
Remove the Old Handle
If your window handles are damaged or not properly fitted, they could cause double-glazed windows to open and close incorrectly. They may even get stuck. This could be due to many reasons, including general wear and tear on the handle or corrosion. In these instances it is essential to seek replacement window handles made of upvc as soon as possible in order to prevent further damage and loss of functionality.
One of the first steps that you should do when replacing upvc window handles is to remove the old handle from the window. Begin by removing the screw covered when the handle in closed position. After you have removed the screw, you can remove the handle. It is possible to make the task simpler by using an electric screwdriver.
Be aware that screws can be hidden beneath caps made of plastic. It is best to remove the covers using a Stanley knife. After the handle has been removed, you must look at the square cut out at the base of the handle to ensure that the new window lock handles are compatible with it. It is essential to measure the length of the spindle on the old handle and compare it to the dimensions of the window mechanism spindle cutout.
There are three types of Upvc handles: Espag handles with a central screw that can be turned left or right and Cranked handles that have two screws and Spade handles that are made of flat arms and can be used on either side of the window made of upvc. It is easy to replace the handle once you have found one that is suitable. Just screw it into place, and ensure that the spindle is correctly inserted in the lock mechanism. Once you have done this you can tighten the handle onto the window frame. Your replacement upvc handles will now be secured.
Take a look at the Spindle
If you need to replace a upvc handle that has fallen, it's likely that the spindle that holds it in place is damaged or is loose. In some cases it is possible to tighten the spindle by using pins or screws. In some cases, it may be necessary to replace the handle. There are many different kinds of handles made of upvc. There are three kinds of handles: inline espagnolette, cockspur, and tilt-and-turn. Each kind has a distinct procedure for installing and replacing the handle.
Before purchasing a replacement handle it is essential to know the size of the handle that is currently in use. This will ensure that the handle fits the window properly and will be of the correct size. All handles are measured according to industry standards, so it is easy to find the correct size.
To determine the size of the handle move the window to the open position. You should then be able see the size of the screw or pin that secures it. Then, use a tape measure or ruler to determine the length of the spindle. Once you have determined the length of the spindle you can buy a new one with exactly the same size.
The step height of a window handle is another factor to consider when buying an alternative. The step height is measured from the base to the point where the handle is placed on the frame. It is typically about 21mm or 9mm for aluminium and uPVC. Dropping objects into the gap will allow you to observe how far the handle extends before it comes into contact with an obstruction.
Cockspur handles typically have different backset heights depending on the style of window they are placed in. Inline the espag handle heights range from 43mm from centre to center (two fixing points). Cockspur handles have different backsets, based on the window they are located in. This is because they have an extension spur that extends from the handle and then locks over a cockspur wedge striker.
Install the new handle
After you've chosen the new handle, make sure it is aligned with the holes for screws on the door. Then, secure it with the screws supplied. If you're replacing the latch lever, it can be installed in a similar way to the main door handle. After that, attach the door trim in order to conceal the mounting screws and close off your project.
Tips: To take the head made of metal from the wedge of wood Hold the handle so that its longer end is resting on the floor and use an hammer to tap the thin end of the handle. Be careful not to scratch the handle or handle spindle.